Project files: ICEpower integrated amp board

What is it?
The project files for the “all-in-one” (nearly…) PCB for making integrated ICEpower amps shown in the previous post.

How big are the boards?
The board measures 2.65″ x 3.15″ (app. 67 x 80 mm.).

What is the status of the boards?
The board is version 2.1. As mentioned, it’s an old design that I have revised and updated to give it the 2.x version number. I’ve built my prototype on a v2.0 board and made some minor tweaks to that before publishing.
The changes in v2.1. are mostly mechanical (too little space for the input connectors etc.) and then minor touch-ups to the silk screen.

Does it use any special/expensive/hard-to-find parts?
No. The overall circuit is quite simple and only a few parts require a bit of attention.

  • The relays are standard mid-sized “2 form C” contact types. If you’re buying from scratch I’d recommend the Takamisawa RY-12W type, but there are app. 1 million equivalents with similar specs and footprint, so you may be able to get good surplus deals as well :). The coil voltage must be 12V.
  • The voltage regulators are standard 7812/7912 types but as they are mounted very close together I recommend the fully-insulated versions. I prefer the ones made by NJR as opposed to ST because the ST-ones seem to behave a bit strangely sometimes (and yes, I might be imagining this…).
  • See BoM-file for description of other parts and values.

Anything else I need to know?
A few things:

  • The on-board parts draw no current from the negative PSU rail. If you’re not using any external circuitry you can omit the negative rail (regulator etc.). If you build it anyway and get strange results, note that some regulators do not like a “no-load” condition and will give an weird unregulated output if not loaded. You can solder a 1-3k resistor on the bottom if you want for added peace of mind.
  • ASP/ASC-usage: It’s possible to use the board with ICEpower ASC and ASP modules. As these include a regulated +/- 12V AUX supply, you should jumper the regulators and the input resistors. The capacitors and remaining components can be left in.
  • Mute-header: The Mute-header simply brings the two pins required for the module’s mute or standby pins to work to a header at the from of the board to simplify wiring. Refer to the datasheet for the respective modules for details on how to use this, but in general you can switch using a mechanical switch.
  • Heat sinking: There is no heat sinking of the regulators as standard. With a simple preamp and no additional load this should not be necessary, but if you want to draw more power then use a small bit of metal as the heat sink. There is not much space in either direction, so using insulated regulators will once again be an advantage.
  • If you prefer a manual input switch, the board is just about ready and will be presented as part of another project post in a few weeks 🙂

Downloads:
Download design files here

Related information:
Please read the FAQs in the original post as well. The picture below shows my “in progress” prototype amp with the Minipre and a 50ASX-module and gives an idea of the expected layout.

Note: Always read the “intro post” for additional important information about my designs.

ice-int-wip

 

Advertisements

2 Responses to Project files: ICEpower integrated amp board

  1. Pingback: Project files: Universal selectors (part 1) | theslowdiyer

  2. Pingback: Project files: Universal selectors (part 2) | theslowdiyer

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: