More JLHs…

Yeah I know, I should probably stop making these at some point 🙂

We’ll do this one quickly then: Standard JLH1969 Ebay-board with upgraded components and better transistors (MJ15003). Fan-cooled heat sink with temperature control (we’ll see how well that works…). Industrial-grade 10A switching PSU per channel. Monoblock configuration in Modushop GX288 chassis.

The PSUs (Artesyn NLP250) are overkill for this application but they were cheap (surplus items). And besides, more is better – right? Not necessarily here though, because some of these industrial-grade PSUs have a reputation for being extremely noisy at low power output. As a class A amp, the max. current consumption of the JLH should be twice its quiescent current (so app. 2.6A) and each PSU will deliver four times that before the limiter kicks in. Whether this is a real problem here or not I don’t know yet, but there are no audible artifacts at all so I am not overly concerned right now.

The heat sinks were also surplus items and I am not sure exactly what their rating is. At full speed the fans are a bit too noisy for my liking (the heat sinks add some flow noise as well) but if the fan speed is lowered a little I don’t think it would be really noticeable once the amps are seated in a rack. For the time being I have installed some small temperature speed control boards for the fans (hence the somewhat messy wiring) but depending on how well that works and how hot the amplifiers get, I may go back to fixed resistors. The PSU already has a dedicated 12V fan output so the resistor doesn’t need to drop a lot of power.

The heat sinks had a cutout in the side that was just too narrow for the angle brackets to fit into. The best solution would have been to mill the ends of the brackets to fit the cutout so there is only one contact surface. Unfortunately I don’t have access to a mill anymore so I had to find another solution: A copper “heat slug” to fill the gap. Just a piece of copper bar in the right thickness cut to size and with thermal grease on both sides and that should provide the best possible thermal transfer under the circumstances.

So, will I stop building these amps? Erm, no! 😀 I am out of the ebay-boards but I do however still have my own version of the 1969 JLH that isn’t cased up yet. This build has given me some inspiration for how I can build that into small monoblocks so while it might take a while to do at least I know what parts to keep my eye out for 🙂

Project files: High current regulators

What is it?
These are high-current regulators designed for LM/LT108x-type regulators with current limits up to 5A or 7.5A dependent on the package. There are two versions, one with an on-board heat sink (as used to power the JLH1969 here) and the other without an onboard heat sink. The PCB with heat sink is intended for regulators in TO-220 packages. This will give you up to 5 amp current capability with an LM338 or a LM/LT1084 reglator IC. The PCB without heat sink is intended to use a TO-247 packaged regulator (LM/LT108xCP – up to 7.5A output current) and should be mounted on a suitable heat sink instead. Whether you use one or the other board version, remember to always calculate the heat dissipated in the regulator – if you are expecting to draw a couple of amps or more, the heat dissipation in the regulator quickly becomes quite large.
Also included is a small DC-DC regulator that fits on top of both regulator PCBs and can be used to generate an additional DC voltage from the main rail to power auxillary circuitry. Depending on the voltage differential and current draw, the AUXreg can use either a standard 78xx regulator or a switching type like the Traco TSR-1 or the Recom R78xx. The compact size means it can also be used as a “voltage thief” in many other places where you have a main DC supply but need a small extra DC voltage for a fan, a microcontroller or similar.

How big are the boards?

  • Regulator with heatsink (onboard-HS): 3.925″ x 20″ (app. 100×51 mm)
  • Regulator without heatsink (non-HS): 2.0″ x 2.0″ (app. 51×51 mm)
  • AUXreg: 0.4375″x2.0″ (app. 11x51mm)

What is the status of the boards?
The onboard-HS board is in v1.1. I built v1.0 and made some small adjustments subsequently, including moving the regulator footprint a little forward because it was too close to the heat sink and also tweaked the silkscreen a bit.
The AUXreg and the non-HS regulator are both in v1.0. I have built the AUXreg and it seems to work well as-is. I haven’t built the non-HS regulator but it is electrically identical to the onboard version it should be fine.

Does it use any special/expensive/hard-to-find parts?
Not really. The only potential exception is if your application requires a switching regulator for the AUXreg board – they can be a bit expensive.

Anything else I need to know?

  • The output voltage on the main regulator can be variable within a certain interval. If R1 is 121R, R2 will set the minimum output voltage (use my spreadsheet to calculate) and using a 500R/1k trimpot for P1 will give app. a 5V/10V adjustment range on the output from the minimum voltage. Note that with R1 = 121R, then C3 should be at least 22uF.
  • For the small caps on the main regulator boards, I recommend types that are rated for a 105C operating temperature as these sit very close to the heat sink. A 105C rating will help improve the reliability and overall lifespan of the caps.
  • The on-board heat sink is a Fischer type SK68/50. It is possible to fit a 40mm fan to the slots on top for improved heat dissipation.
  • Mounting considerations: Mounting the regulator and the PCB to the SK68 heat sink requires a bit of manual support because the screws tend to “slip” sideways in the slots. Also, you’ll want to mount the C1 capacitor last as it obscures the access to the mounting screw for the regulator.
  • For the AUXreg: The cap values C1 and C2 should be 330nF and 100nF respectively (ceramic or film types) for an 78xx regulator. For a switching regulator normally only a small electrolytic is required at the C1 position, but please consult the datasheet for the specific regulator you are using to be sure.

Downloads:
Download design files here

Related information:
Note: Always read the “intro post” for additional important information about my designs.

Always read the manufacturer’s datasheets for regulators etc. to confirm component values are correct. Even for “generic” types there may be slight differences between each manufacturer’s recommendations.

Project files: Mini JLH1969

What is it?
This is the project files for my version of the JLH1969 amplifier as shown here. The files for the matching PSU will follow shortly.

How big are the boards?
The board measures 2.25″x2.3″ (app. 57x58mm).

What is the status of the boards?
The board is in version 1.0. I have built and tested a couple of prototypes (as described in the original post) and although they play music just fine, you should still consider this a “work-in-progress”. I would be especially concerned with confirming the thermal stability of the amp because of the compact dimensions, so if anyone decides to build this please share your results 🙂
EDIT 17th Jan. 2016: Added v1.1 of the files in a separate link below. Minor tweaks to the board and the download now includes a basic BoM as well.

Does it use any special/expensive/hard-to-find parts?
No. I have used MJL21196 output transistors because I had them, but versions of the MJE/TIP3055 should be OK as well as long as they are in suitable (meaning TO-247 or TO-264) packages. Do not be tempted to use faster transistors such as the MJL/NJL3281-types as the amp will most likely not be stable with these. Have a look at the TCAAS page on transistor substitutes for more info.

Anything else I need to know?

  • The only change I have done from the original schematic is to replace R5 with a 200k trimpot to make it easier to adjust the operating point. Oh, and I’ve made up designators for the parts that don’t have a number on the original schematic 😉
  • In my opinion the output cap should be 4700uF or larger, even with an 8 ohm load. Even if the supply voltage is 27V, I’d be comfortable with using a 25V cap in this position. All the other electrolytics should be 35V or higher.
  • Heat sink T3 as it might get hot. You’ll probably not be able to find a standard heat sink that fits. so my recommendation would be a small piece of bent aluminium or copper with a hole tapped in it for easy mounting.
  • Raise the R2 resistor 5-10 mm above the board for cooling (I haven’t done this in the prototype version but it gets quite hot).
  • The footprint for the input transistor is for a 2N3906 as described in the original BoM, but other types can be used as well. An easy to get choice is a BC560C which needs to be turned 180 deg. in order for the footprints to match.

Downloads:
Download design files here (v1.0)
Download design files here (v1.1 – added 17th Jan. 2016)

Related information:
Note: Always read the “intro post” for additional important information about my designs.

As usual, both TCAAS and this diyaudio.com thread contains lots of worthwhile information.

minijlh1969pcb-1

JLH 1969 PSU

As promised, here is the matching PSU for the mini JLH1969 amp. Based (roughly) on the PSU designed for the JLH1996 amp, this is a single-rail regulated PSU based on an LM1084 (or LM338) regulator giving a 5A current limit. The board measures 5×10 cm and is intended to be used for one amplifier channel. The onboard heat sink is a Fischer SK68/50 which should be enough for an amp that draws app. 1.3A, especially if the low-drop LM1084 regulator and a suitable transformer is used.

The PSU works, but I haven’t had time to test it properly with the amp just yet (hopefully in the coming weekend). More pictures and information when that is done and I can post the project files 🙂

jlh1969psu-1

JLH 1969 revisited…

Finally a bit of progress around here 😀

Even though I have already built a Linsley-Hood JLH1969 clone and another is in the works, I still wanted to make my own layout for this classic amplifier – and here it is!.

The board measures measurements are 2.3″ by 2.25″ (app 57×58 mm.) and as usual the layout is as tight (some would say “cramped” as I could make it. The transistors used are based on Geoff Moss’ recommendations. I actually have some NOS 2N1711, but the BD139-16 actually measures better (higher hfe). The output devices are MJL21196 because I had them available and because the larger TO-264 package is nice.

The board will be powered by a regulated PSU (hopefully ready shortly – the last parts are in the mail) based on a normal 3-pin regulator as shown in the 1996 JLH article (if all these references seem a bit like you have to be “in-the-know” to keep up, I suggest you start reading the pdf-articles here instead 🙂 ).

Now, I haven’t really done much with this beyond testing that it plays music, but when the PSUs are up and running I’ll look into more testing. In terms of value-for-money this isn’t likely to compete with the cheap ebay-kits, but hey – if I wanted to save money I wouldn’t be building amps I would just buy one that worked! 😀

JLH build(s) update

A couple of my projects that are seeing some progress at the moment are my JLH amplifiers. The JLH1969 clone boards have come a bit further as I managed to fabricate/order most of the enclosure for them. Still to go is mounting a fan control board in the enclosure and then finishing up the wiring of everything. The PSU is a Mean Well 27V USP-350 which should be more than adequate for the job – let’s hope it sounds good as well.

My upgraded JLH boards are also coming along nicely. These are based on Geoff Moss’ updated JLH design and meant to be as compact as possible. In some places, I think I have overdone it a bit but assuming everything works I am very satisfied 😀

I had a few problems with getting the offset right but after some help from some nice folks at diyaudio, it turned out that it was just a wrong value for a trimpot. After than was fixed, the assembled boards are now playing in a somewhat improvised test setup (see pictures). The boards are of course not thermally stable in this setup, but it is enough to confirm that it is possible to adjust the quiescent current, zero the DC offset etc. and that they actually play music :D.

Next up is to figure out a suitable enclosure and drilling heatsinks etc. I also need to sort out a PSU for these and at least for starters I’ll probably try my hand at the capacitance multiplier circuit suggested for the amp.

The JLH amp – prelude

The JLH-amp, or more correctly John Linsley-Hood’s class A amplifier, is probably one of the most well-known designs in DIY audio. The original version was published in 1969, but that’s a little before my time. I first started reading about the design when Linsley-Hood published an updated version of it in the magazine Electronics & Wireless World in 1996. For me, the JLH is one of those designs that tick all the boxes (cheap, simple, good sound quality etc.) and I have been fascinated by it since I first read about it, but I never managed to actually build one.

Since the 1996 article, both the updated and the original versions have been helped back to popularity (or at least dragged out of obscurity) in the DIY audio community  primarily by two things I think:

The first factor is Geoff Moss’s excellent “The Class A Amplifier Site” (TCAAS) resource, now hosted by Rod Elliot of ESP, that started around 10 years ago (ugh, how time flies!). The site collects a lot of information about Linsley-Hood designs as well as other well-known Class A designs from the likes of Jean Hiraga and Musical Fidelity.

The second factor is the proliferation of extremely cheap ebay kits using the original JLH design as basis. Obviously, if you can get a whole kit for less than it would cost most people to manufacture the blank PCB, there’s really no excuse for not trying 🙂 I have bought one of these kits, substituted some key components (namely the caps and the output transistors) for some more “dependable” types (read: of less questionable origin) and mocked it up to see if it works. Below is the state of affairs at the moment, obviously not living-room friendly just yet, but it plays music! I’ve only hooked them up to my test speaker, but it is going to be fun listening to these once I get an enclosure ready for them.

JLH board on heatsink for testing.

 

Now the real point of this post is actually that I am working on a PCB based on Geoff Moss’s updated version here:

It’s still not quite ready yet, but the PCB design files have been shipped off to manufacturing and should be back within a couple of weeks. More to follow when I have one assembled.

/U.