Linear PSUs are better…

…aren’t they? 😀

No, I don’t really want to start up that discussion here because in my opinion it’s much more complex subject than most audiophiles believe. However, one thing that is obvious is that as more and more small audio components run on single DC rails from an external PSU (streamers, DACs, headphone amps etc.), a fairly large market for aftermarket “upgrade” PSUs has opened up. Some manufacturers (e.g. Auralic) even offer separate PSUs as upgrades themselves. Well, a linear PSU is normally a relatively simple thing so why not DIY it?

Since I now have a DAC, a preamp, a streamer and quite a few other things that run on single-rail DC this seems a worthwhile project and it’s actually been on the drawing board for a while. I did have a bit of trouble getting started on the circuit and layout though, and I didn’t manage to really break the deadlock until remembered a design called STEPS by headwize/head-fi user Tangent from (many) years ago. The design isn’t up anymore, but thankfully I managed to locate it on the wayback-machine.

It’s basically a standard LM317-based PSU, but with a few tweaks added to tease as much performance as is possible out of the LM317 regulator (or one of its many derivatives). My version isn’t a straightforward copy of the STEPS, but I owe a big thanks to the the STEPS all the same. Compared to a “normal” LM317-based circuit this one includes:

  • A simple mains filter on the primary side of the transformer.
  • A snubber circuit on the secondary side of the transformer.
  • Space for high-speed/soft recovery diodes and snubber caps.
  • Space for 2+2 18mm filter capacitors in C-R-C (pi-filter) configuration before the regulator.

Everything else looks like the “high-performance” circuit variation from the data sheet of any LM317-type regulator. The onboard transformer is a 25VA Talema PCB-mounted toroid type meaning the design should be good for most applications requiring less than app. 20W power. The 15VA type transformer will fit as well and allow for mounting in a 1U enclosure, but the constraints on heat sinking and capacitor height might then be an issue.

The pictures show the completed 12V prototype for my Arcam IRdac as well as a partially completed 16V board for an Auralic Aries Mini (a recent purchase) – I’m waiting for a transformer in the mail before I can finish that and test it 🙂

Project files: GP-PSUs v2

What is it?
Two boards for general-purpose LM317/LM337 power supplies with two rails, useable for many low-power applications (preamps, buffers, filters etc.). There are two versions, one where the +/- voltage is derived from a single AC-voltage via a voltage-doubler and one where it comes from a traditional dual-AC, two-bridge rectifier circuit.
These boards are effectively an update on the old GP-PSUs and they are based on the triple-PSUs I posted a while ago. In fact they are just the three-rail designs with the third rail removed 😀

How big are the boards?
Both board versions measure 3.925″ x 1.8″ (app. 100 x 46 mm.) and they are mechanically interchangeable.

What is the status of the boards?
Both boards are in v1.0. I haven’t actually prototyped these in this format yet, but since they are the same as the three-rail version (which I have tested) I don’t mind publishing them.

Does it use any special/expensive/hard-to-find parts?
Nothing, really. As always with these circuits, you can use standard LM317/337 regulators or splash out on more expensive (low-dropout) types like the LT/LM/LD108x-series. My experiences with the latter parts aren’t the greatest though (instability), so unless your applications require the low-drop capability I’d just as well stick to standard 317/337-types from a reputable source. If your application requires a higher performance PSU than this, you are probably better off looking at entirely different circuits and regulators anyway.

Anything else I need to know?
Yes, pretty much a repeat of what was mentioned for the three-rail circuits:

  • The diameter of the main filter capacitors is 18mm, but the dual footprint means that anything between 10mm and 18mm should be fine.
  • The DIP rectifier bridges exist in versions up to 2A rated current although anything more than 1A can be a bit difficult to find. Realistically though, if you plan on drawing more than 1A from either supply the SK104-type heat sinks are probably going to be a limiting factor anyway.
  • Mounting the regulators and heat sinks is a bit of a faff because there is not much space, especially if the heat sinks are 38mm or taller. My suggestion (as always) is something like this:
    • 1) Loosely assemble the regulator, the isolation components and the heatsink.
    • 2) Mount the combination on the PCB and solder the heatsink in place.
    • 3) Tighten the screw holding the regulator to the heatsink.
    • 4) Solder the regulator in place.

Downloads:
Download design files here

Related information:
Even though the regulators used here are generic types made by many manufacturers, there can be small differences in recommended parts values etc. I suggest you always consult the regulator data sheets from the specific manufacturer.

Note: Always read the “intro post” for additional important information about my designs.

Project files: Universal Triple-PSUs

What is it?
Two boards for general-purpose LM317/LM337 power supplies with three rails, useable for many low-power applications where both a +/- supply and an auxiliary voltage are needed. Examples include analog amplifier + digital/logic circuitry, microphone preamplifier + phantom voltage etc.
There are two versions, one where the +/- voltage is derived from a single AC-voltage via a doubler and one where it comes from a traditional two-bridge rectifier circuit. This design is virtually a copy of my GP-PSUs. I made some minor enhancements and added the extra rail, but it is the same basic design.

How big are the boards?
Both board versions measure 3.925″ x 2.6″ (app. 100 x 66 mm.) and they are mechanically interchangeable.

What is the status of the boards?
The “standard” board is in v1.0 and works fine. The voltage-doubled board is in v1.1 and also works fine. The two versions are completely identical except for the diode/bridge arrangement on the +/- supply. The difference in version numbers came because I originally prototyped a different (smaller) layout for the voltage-doubled version. After making the “standard” version that requires a bit more space for the rectifier bridges, I decided it was smarter if they were both the same size and then changed the layout of the voltage-doubled board to match.

Does it use any special/expensive/hard-to-find parts?
Nothing, really. As always with these circuits, you can use standard LM317/337 regulators or splash out on more expensive (low-dropout) types like the LT/LM/LD108x-series. My experiences with the latter parts aren’t the greatest though (instability), so unless your applications require the low-drop capability I’d just as well stick to standard 317/337-types from a reputable source. If your application requires higher performance than this, you are probably better off looking at entirely different circuits and regulators.

Anything else I need to know?

  • There is a jumper on the boards that links the ground on the AUX-voltage to the midpoint (0V) of the +/- supply. This is optional and probably not required for most applications but can be used for e.g. linking analog and digital ground in mixed-signal circuits.
  • The diameter of the main filter capacitors is 16mm on the AUX supply and 18mm on the main supply.
  • The DIP rectifier bridges exist in versions up to 2A rated current although anything more than 1A can be a bit difficult to find. Realistically though, if you plan on drawing more than 1A from either supply the SK104-type heat sinks are probably going to be a limiting factor anyway.
  • Mounting the regulators and heat sinks is a bit of a faff because there is not much space, especially if the heat sinks are 38mm or taller. My suggestion (as always) is something like this:
    1) Loosely assemble the regulator, the isolation components and the heatsink.
    2) Mount the combination on the PCB and solder the heatsink in place.
    3) Tighten the screw holding the regulator to the heatsink.
    4) Solder the regulator in place.

Downloads:
Download design files here

Related information:
Even though the regulators used here are generic types made by many manufacturers, there can be small differences in recommended parts values etc. I suggest you always consult the regulator data sheets from the specific manufacturer.

Note: Always read the “intro post” for additional important information about my designs.